VENTO SOLO A60 wall ventilator with heat and energy recovery from BLAUBERG is an indoor ventilation system without the need for ducts. Ensures the supply of clean fresh air, with air being alternately extracted and supplied, while at the same time preserving the heat of the room, thanks to its ceramic exchanger with an efficiency of up to 85%. In addition, it ensures a balance in humidity levels in the room thanks to the built-in humidity sensor.
Features:
- Energy class Α.
- Air flow up to 60m3/h.
- Built-in filters with class G3 to clean supply and extract air flows, washable and easily removable.
- Low Power Consumption from 1.20W.
- Control via remote control.
- Reducing the cost of heating in winter and cooling in summer.
- Protect against outdoor noise.
- Prevent penetration of excessive humidity and appearance of mould.
- It does not require condensate drainage.
- The motor has overheating protection and bearings for longer life.
- The air duct can be extended by a pipe of the same diameter at a distance of up to 3m.
- Suitable for replacing an existing fan with minimal intervention.
Remote control
Product cutting VENTO SOLO A35, A50 & A60 V2
VENTO SOLO A35, A50 & A60 V2 installed in the building
Operation logic - 2 Cycles:
1st Phase (Air Extract)
- The ventilation unit exhausts the indoor air with the help of a fan, which passes the air through the heat exchanger for 70 seconds.
- The exchanger (ceramic element) stores the heat of its exhaust air so that it is available in the next phase.
2nd Phase (Air Supply)
- Once the 70 seconds are up, the system changes the direction of rotation of the fan, which now introduces fresh air from the environment into the interior.
- The incoming air passes through the exchanger where it absorbs (recovers) the stored, from the 1st phase, heat.
- Thus the fresh air is introduced into the interior, preheated and clean.
- Thanks to the filters the incoming air is free of dust, viruses, pollen and suspended particles.
- As soon as the 70 seconds of the second phase are completed, the system continues its operation, constantly repeating the cycle described above.
- This ensures the continuous renewal of quality air to the interior space, maintaining its thermal comfort.
Technical Characteristics:
| |
VENTO SOLO A35
|
VENTO SOLO A50
|
VENTO SOLO A60
|
|
Air flow in ventilation mode minimum speed / maximum speed m3/h
|
30 / 46
|
25 / 50
|
35 / 60
|
|
Air flow in heat recovery minimum speed / maximum speed m3/h
|
15 / 23 |
12,5 / 25 |
17,5 / 30 |
|
Ceramic heat exchanger efficiency
|
Up to 85%
|
|
Noise at maximum speed (3m) dB(A)
|
26
|
29
|
29
|
|
Noise at minimum speed (3m) dB(A)
|
21
|
16
|
27
|
|
Transported air temperature °C
|
-15... + 40
|
|
Energy consumption minimum speed / maximum speed W
|
1,50-2,30
|
0,70-2,30
|
1,10-3,20
|
|
Included filters
|
2
|
|
Class Filter
|
ΕΝ 779 G3
|
|
Energy class
|
A
|
|
Power supply Vac
|
220-240
|
|
Ingress protection rating
|
ΙΡ24
|
|
Diameter
|
∅106
|
∅131
|
∅156
|
Total dimensions [mm]:
| |
∅ D |
B |
B1 |
L |
L1 |
L2 |
| VENTO SOLO A60 |
156 |
205 |
186 |
305-380 |
35 |
86 |
Energy labels:
